All pool and spa filtration systems, with the use of multiple devices. One of the most important are the filter of your spa or pool pump. A mechanical seal is a key component in the design of these pumps. The purpose of a seal is to prevent water damage to the drive shaft of the pump.

Damage to the seals of the thermal pool and the pumps are due to overheating, vibration, and a sudden change in water pressure. There are someCases where the dirt captured between the surfaces of the seal. This can damage the seal and results in a loss. Once you have a loss on the pump to develop, it will only get worse, and even the seal replaced.

Glass Replacement Beaker

Steps to successfully complete the sealing of the pump

Before starting the repair of a swimming pool pump, you must need the necessary tools and spare parts to complete the work on the collection. Tools and resources are:
A pair of pliers. ARatchet good September A key to the small wheel. A rubber mallet or a shopping mall. A series of flat screwdriver. Some emery sandpaper. Silicone lubricant. New seal assembly. Make sure that the correct model for the pump seal is a model. You can check this by the manual or the manufacturer of the pool pump. A replacement seal for the pump body. Anti-Seize. For the coating of the wires of the motor.

Replace pump shaft seal

UsuallyA general rule to follow, all security whenever maintenance of electrical equipment of any kind. Otherwise it could cause serious injury or death to bring himself or others.
Before beginning repairs on your pool filter pump, disconnect the power. Be sure to lock the main switch and the next day. This is an added security measure, not to prevent someone accidentally damaged if the circuit breaker. Close valvesboth the suction and pressure side of the pump. To access the damaged seal on the pool pump, remove the four hex screws. These are the four screws connecting the motor and pump impeller. Keep the engine with both hands and shake it from side to side a bit '. This allows you to successfully extract the engine and its mounting assembly from the pump casing. Use your pliers or a crescent wrench, hold the end of the extended engineWave (backend). Thus, the crankshaft can move around more. Now take your key and remove the wheel from the wheel of the pump. If you are not handy with a paddle wheel key, you can take an old rag over the fan and tighten by hand. The flap is in the mind, stop cutting yourself on sharp edges of the wheel to help. There is also another option, but it is the last resort. Use one of your own against the wheel and tap with your rubber-Mall. Be very careful not toto break or damage the impeller. The seal plate should now be removed from the pump motor. This is done by removing the four small screws that hold it in place to reach. After the screws are removed, gently tap to release the seal plate of the motor. Now, before removing the seal, it should be noted, as was originally installed. This will help you install the new pump shaft seal.Now help with a small flat screwdriver to drive the distance of the rotating partthe party who is holding component.The fixed in the cavity of the seal on the upstream of the motor. To lose weight you need to turn around the seal plate. The fixed part of the estate is down now. Place the tip of a screwdriver on the back of the seal and throw it outside. Use sandpaper to clean the water and a bit 'on the shaft / sleeve and the engine compartment seal the plate. Place a small amount of silicone grease on the engine isand sealing the recess. This lubrication helps the assembly held in place a little 'easier to slide. Make sure you install both halves of the seal assembly in the same way as the original. The white ceramic part of the seal with the cup goes in the pot black rubber seal. The surface of glass to you. The other part of the seal (rotating part with the spring) is on the motor shaft. This is only after the motor mount bolt back inPlace. You must use extreme caution here, because you do not want to damage, dirt and scratches the faces of your new seal. Check pump for leaks and if it is damaged in any way, replace it. Well, if the pool pump introduces a paper seal (rotary pumps), they will surely be replaced. To be honest! If you disassemble a pump to seal the original seal usually is not new. Before installing the new pump, head gasket, you have all traces of the old. This will ensureensures correct positioning of the new order for a proper seal. If you need to replace the cylinder head gasket of the pump, put the new between the two halves of the pump. Now replace the pool pump in reverse order it removed. Finally, the valves open on the pump intake and exhaust. Restore power and restart it. Check for signs of leakage. There are some cases where you use a paper seal, that a small loss may be obvious, butOnce the seal is wet you create a proper seal. In some cases, one or two laps on the pump bolts. Yet, if you follow the instructions for your pump repairs a success.

Normally the manufacturer of spa and pool pumps will recommend to you to repair the pump. This will keep your warranty and prevent injuries. However, if the guarantee is in place and a little 'short of money, I say go for it, and do theirRepairs. But always check with your opinion and adequate safety measures first. The producers also prefer people who work on their products qualified to do so.

But then I think with the right instruction you or I can successfully replace a pump seal. Next! We save a lot of money process and the learning experience is priceless. For more information on how to correct with a pool and spa, visit my site. Click on the linkbelow in the resource box and a tour. See over there, and the blessing of God

Email This BlogThis! Share to Twitter Share to Facebook

Loved this post? Then why don't you share It!